The "STATUS" column gives the latest known status of the standard.
If a standard has been withdrawn and no replacement specification is listed, either the specification was withdrawn without replacement or a replacement specification could not be identified.
DIN stands for "Deutsches Institut für Normung", meaning "German institute for standardisation". DIN standards that begin with "DIN V" ("Vornorm", meaning "pre-issue") are the result of standardization work, but because of certain reservations on the content or because of the divergent compared to a standard installation procedure of DIN, they are not yet published standards.
DIN ISO 5456-1, DIN ISO 5456-2, DIN ISO 5456-3, DIN ISO 5456-4
ISO 5456-1, ISO 5456-2, ISO 5456-3, ISO 5456-4
DIN 5-10
Technical drawings - projections, terms
Withdrawn
DIN ISO 10209-2
ISO 10209-2
DIN 6
Projection displays in Normal, views and special presentations
Withdrawn
DIN ISO 128, DIN EN ISO 128
ISO 128
DIN 7
Parallel Pins
Withdrawn
DIN EN ISO 2338
ISO 2338
DIN 11
Whitworth pipe threads 1/4"-6" Thread diameter, sizes, teaching information
Withdrawn
DIN 13-1
ISO general purpose metric screw threads - Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mm
Active
DIN 13-2
ISO general purpose metric screw threads - Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm
Active
DIN 13-3
ISO general purpose metric screw threads - Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm
Active
DIN 13-4
ISO general purpose metric screw threads - Part 4: Nominal sizes for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110 mm
Active
DIN 13-5
ISO general purpose metric screw threads - Part 5: Nominal sizes for 1 mm and 1,25 mm fine pitch threads; nominal diameter from 7,5 mm to 200 mm
Active
DIN 13-6
ISO general purpose metric screw threads - Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mm
Active
DIN 13-7
ISO general purpose metric screw threads - Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mm
Active
DIN 13-8
ISO general purpose metric screw threads - Part 8: Nominal sizes for 3 mm fine pitch threads; nominal diameter from 28 mm to 300 mm
Active
DIN 13-9
ISO general purpose metric screw threads - Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mm
Active
DIN 13-10
ISO general purpose metric screw threads - Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm
Active
DIN 13-11
ISO general purpose metric screw threads - Part 11: Nominal sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to 1000 mm
Active
DIN 13-12
ISO general purpose metric screw threads - Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitches
Active
DIN 13-13
ISO general purpose metric screw threads - Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizes
Active
DIN 13-19
ISO general purpose metric screw threads - Part 19: Nominal profiles
Active
DIN 13-20
ISO general purpose metric screw threads - Part 20: Limits of sizes for coarse pitch threads with the preferred tolerance classes; nominal sizes from 1 mm to 68 mm
Active
DIN 13-21
ISO general purpose metric screw threads - Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm
Active
DIN 13-22
ISO general purpose metric screw threads - Part 22: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 25 mm to 52 mm
Active
DIN 13-23
ISO general purpose metric screw threads - Part 23: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 53 mm to 110 mm
Active
DIN 13-24
ISO general purpose metric screw threads - Part 24: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 112 mm to 180 mm
Active
DIN 13-25
ISO general purpose metric screw threads - Part 25: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 182 mm to 250 mm
Active
DIN 13-26
ISO general purpose metric screw threads - Part 26: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 252 mm to 1000 mm
Active
DIN 13-28
ISO general purpose metric screw threads - Part 28: Coarse and Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root Cross-sections, Tensile Stress Cross-sections and Pitch Angles
Active
DIN 13-50
ISO general purpose metric screw threads - Part 50: Combination of tolerance classes for formed internal screw threads
Active
DIN 13-51
ISO general purpose metric screw threads - Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes
Active
DIN 13-52
ISO general purpose metric screw threads - Part 52: Multi-start thread tolerances and deviation of profile
Active
DIN 16
Oblique Standard Typeface for Drawings
Withdrawn
DIN 17
Upright Standard Typeface for Drawings
Withdrawn
DIN 76-1
Thread run-outs and thread undercuts for ISO metric threads in accordance with DIN 13-1
Active
DIN 76-2
Thread run-outs and thread undercuts for pipe threads conforming to ISO 228 part 1
Active
DIN 76-3
Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and Knuckle Threads and other Threads of Coarse Pitch
Active
DIN 78
Protrusions of bolt ends
Active
DIN EN ISO 4753 (governs thread ends for bolts assembled with hexagon slotted nuts)
ISO 4753
DIN 84
Product grade A slotted cheese head screws
Withdrawn
DIN EN ISO 1207
ISO 1207
DIN 85
Product grade A slotted pan head screws
Withdrawn
DIN EN ISO 1580
ISO 1580
DIN 93
Tab washers with long tab
Withdrawn
DIN EN ISO 1234
ISO 1234
DIN 94
Split pins
Withdrawn
DIN EN ISO 1234
ISO 1234
DIN 95
Slotted Raised Countersunk (Oval) Head Wood Screws
Active
DIN 96
Slotted Round Head Wood Screws
Active
DIN 100 to DIN 199
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 103-1
ISO Metric Trapezoidal Screw Thread; Profiles
DIN 103-2
ISO Metric Trapezoidal Screw Thread; General Plan
DIN 103-3
ISO Metric Trapezoidal Screw Thread; Allowances and Tolerances for Trapezoidal Screw Threads of General Purpose
DIN 103-4
ISO Metric Trapezoidal Screw Thread; Nominal Dimensions
DIN 103-5
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal Diameter
DIN 103-6
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 105 to 300 mm Nominal Diameter
DIN 103-7
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 8 to 100 mm Nominal Diameter
DIN 103-8
ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 105 to 300 mm Nominal Diameter
DIN 103-9
ISO metric trapezoidal screw threads; gauging of external and internal threads; gauge dimensions and design features
DIN V 105-1
Clay masonry units - Part 1: Solid and hollow bricks with density classes of 1,2
Withdrawn
DIN V 105-100, DIN EN 771-1
EN 771-1
DIN V 105-2
Clay masonry units - Part 2: Solid and hollow bricks with density classes equal 1.0
Withdrawn
DIN V 105-100, DIN EN 771-1
EN 771-1
DIN 105-3
Clay masonry units - Part 3: Tile and high strength-high-strength clinker
Withdrawn
DIN V 105-100, DIN EN 771-1
EN 771-1
DIN 105-4
Clay masonry units - Part 4: Ceramic bricks
Withdrawn
DIN V 105-100, DIN EN 771-1, DIN EN 772-7
EN 771-1, EN 772-7
DIN 105-5
Clay masonry units - Part 5: Lightweight long-hole brick and light long-hole brick panels
Active
DIN V 105-6
Clay masonry units - Part 6: High precision units
Active
DIN V 105-100
Clay masonry units - Part 100: Clay masonry units with specific properties
Active
DIN 125
Washers; medium type, primarily for hexagon bolts
Withdrawn
DIN EN ISO 7089, DIN EN ISO 7090
ISO 7089, ISO 7090
DIN 125-1
Product grade A washers - with a hardness up to 250 HV designed for use with hexagon head bolts and nuts
Withdrawn
DIN EN ISO 7089, DIN EN ISO 7090
ISO 7089, ISO 7090
DIN 125-2
Product grade A washers - with a hardness up to 300 HV designed for use with hexagon head bolts and nuts
Withdrawn
DIN EN ISO 7089, DIN EN ISO 7090
ISO 7089, ISO 7090
DIN 126
Product grade C washers - designed for use with hexagon head bolts and nut
Withdrawn
DIN EN ISO 7091
ISO 7091
DIN 127
Spring lock washers with square ends or tang ends
Withdrawn
DIN 128
Curved and wave spring lock washers
Withdrawn
DIN 137
Spring washers, curved or wave
Withdrawn
DIN 200 to DIN 299
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 201
Technical drawings; Hatchings; Representation of cutting edges and materials
Withdrawn
DIN ISO 128-50
ISO 128-50
DIN 209
Machine Reamers with Screwed-on Blades
Active
DIN 267-1
Fasteners - Part 1: Technical delivery conditions; General requirements
Withdrawn
DIN 267-2
Fasteners - Part 2: Technical delivery conditions; Bolts, Screws, Nuts and Similar Threaded and Formed Parts; Types and Dimensional Accuracy
Active
DIN EN ISO 4759-1
ISO 4759-1
DIN 267-3
Fasteners - Part 3: Technical delivery conditions; Property classes for carbon steel and alloy steel bolts and screws; Conversion of property classes
Withdrawn
DIN EN ISO 898-1
ISO 898-1
DIN 267-4
Fasteners - Part 4: Technical delivery conditions; Property classes for nuts (previous classes)
Withdrawn
DIN EN ISO 898-2
ISO 898-2
DIN 267-5
Fasteners – Part 5: Technical delivery conditions; Acceptance inspection; modified version of ISO 3269, 1984 edition
Withdrawn
DIN EN ISO 3269
ISO 3269
DIN 267-6
Fasteners - Part 6: Technical delivery conditions; Designs and accuracy of measurement for product grade F
Active
DIN 267-7
Fasteners - Part 9: Technical delivery conditions; Bolts made of unalloyed or low-alloy steels
Withdrawn
DIN EN ISO 898-1
ISO 898-1
DIN 267-9
Fasteners - Part 9: Technical delivery conditions; Components with Electroplated Coatings
Withdrawn
DIN EN ISO 4042
ISO 4042
DIN 267-10
Fasteners - Part 10: Technical delivery conditions; Hot dip galvanized parts
Withdrawn
DIN EN ISO 10684
ISO 10684
DIN 267-11
Fasteners - Part 11: Technical delivery conditions (with additions to ISO 3506); Corrosion-resistant stainless steel fasteners
Withdrawn
DIN 267-12
Fasteners - Part 12: Technical delivery conditions; Self-tapping screws
Withdrawn
DIN EN ISO 2702
ISO 2702
DIN 267-13
Fasteners - Part 13: Technical delivery conditions; Components for Bolted Connections Made Mainly from Materials Exhibiting a High Impact Strength at Low Temperature or from Materials with a High Temperature Strength
Active
DIN 267-15
Fasteners - Part 15: Technical delivery conditions; Prevailing torque type nuts
Withdrawn
DIN EN ISO 2320, DIN EN ISO 3506-1, DIN EN ISO 3506-2, DIN EN ISO 3506-3
ISO 2320, ISO 3506-1, ISO 3506-2, ISO 3506-3
DIN 267-18
Fasteners - Part 18: Technical delivery conditions; Components made of Non-ferrous Metals
Withdrawn
DIN EN 28839
ISO 8839
DIN 267-19
Fasteners - Part 19: Technical delivery conditions; Surface discontinuities on bolts and screws
Withdrawn
DIN EN ISO 26157-1, DIN EN ISO 26157-3
ISO 6157-1, ISO 6157-3
DIN 267-20
Fasteners - Part 20: Technical delivery conditions; Surface discontinuities on nuts
Withdrawn
DIN EN ISO 6157-2, DIN EN ISO 10484, DIN EN ISO 10485
ISO 6157-2, ISO 10484, ISO 10485
DIN 267-21
Fasteners - Part 21: Technical delivery conditions; Widening test on nuts
Withdrawn
DIN EN ISO 6157-2, DIN EN ISO 10484, DIN EN ISO 10485
ISO 6157-2, ISO 10484, ISO 10485
DIN 267-23
Fasteners - Part 23: Technical delivery conditions; Property classes for nuts with fine thread (ISO classes)
Withdrawn
DIN EN ISO 898-6
ISO 898-6
DIN 267-24
Fasteners - Part 24: Technical delivery conditions; Property classes for nuts (Hardness classes)
Active
DIN 267-25
Fasteners - Part 25: Technical delivery conditions; Torsion testing of M1 to M10 bolts and screws
Withdrawn
DIN EN 20898-7
EN 20898-7
DIN 267-26
Fasteners - Part 26: Technical delivery conditions; Conical spring washers for bolt/nut assemblies
Active
DIN 267-27
Fasteners - Part 27: Technical specifications; Steel screws, bolts and studs with adhesive coating
Active
DIN 267-28
Fasteners - Part 28: Technical specifications; Steel screws, bolts and studs with locking coating
Active
DIN 267-29
Fasteners - Part 29: Technical specifications; Product grades for parts for bolted connections for use at temperatures ranging from -200°C to +700°C
Withdrawn
DIN 267-30
Fasteners - Part 30: Technical specifications; Metric thread rolling screws of property class 10.9
Active
DIN 276-1
Building costs; Part 1: Building construction
Active
DIN 276-2
Building costs; Part 2: Classification of cost
Withdrawn
DIN 276-3
Building costs; Part 3: Ascertainment of cost
Withdrawn
DIN 300 to DIN 399
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 315
Wing nuts with rounded wings
Active
DIN 316
Wing screws with rounded wings
Active
DIN 323-1
Preferred Numbers and Series of Preferred Numbers; Basic Values, Calculated Values, Rounded Values
Withdrawn
DIN 323-2
Preferred Numbers and Series of Preferred Numbers; Introduction
Active
DIN 332-1
60° centre holes; types R, A, B, and C
Active
DIN 332-2
Center holes 60° with thread for shaft ends for rotating electrical machines
Active
DIN 332-4
Centre holes for rail vehicles axles
Active
DIN 332-7
Machine tools; 60° centre holes; dimensioning
Active
DIN 332-8
Centre holes 90°, form S; dimensions, determination process
Active
DIN 332-10
Center Holes; Indications on Technical Drawings
Withdrawn
DIN ISO 6411
ISO 6411
DIN 338
Parallel shank twist drills, jobber series
Active
DIN 400 to DIN 499
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 404
Slotted capstan screws
Active
DIN 406-10
Engineering drawing practice; dimensioning; concepts and general principles
Active
DIN 406-11
Engineering drawing practice; dimensioning; principles of application
Active
DIN 406-12
Engineering drawing practice; dimensioning; tolerancing of linear and angular dimensions (modified version of ISO 406:1987)
Active
DIN 417
Slotted set screws with long dog point
Withdrawn
DIN EN 27435
ISO 7435
DIN 427
Slotted headless screws with chamfered end
Withdrawn
DIN EN ISO 2342
ISO 2342
DIN 428
Hexagon nuts, Grade C
Withdrawn
DIN EN ISO 4034
ISO 4034
DIN 433
Washers for use with cheese head screws
Withdrawn
DIN EN ISO 7092
ISO 7092
DIN 433-1
Product grade A washers - with a hardness up to 250 HV designed for use with cheese head screws
Withdrawn
DIN EN ISO 7092
ISO 7092
DIN 433-2
Product grade A washers - with a hardness up to 300 HV designed for use with cheese head screws
Withdrawn
DIN EN ISO 7092
ISO 7092
DIN 438
Slotted set screws with cup point
Withdrawn
DIN EN 27436
ISO 7436
DIN 439
Hexagon thin nuts
Withdrawn
DIN EN ISO 4035, DIN EN ISO 4036, DIN EN ISO 8675
ISO 4035, ISO 4036, ISO 8675
DIN 439-1
Unchamfered hexagon thin nuts - Product grade B
Withdrawn
DIN EN ISO 4036
ISO 4036
DIN 439-2
Chamfered hexagon thin nuts - Product grades A and B
Withdrawn
DIN EN ISO 4035, DIN EN ISO 8675
ISO 4035, ISO 8675
DIN 440
Washers for use in timber constructions
Withdrawn
DIN EN ISO 7094
ISO 7094
DIN 444
Eyebolts
Active
DIN 461
Graphical Representation in Systems of Coordinates
Active
DIN 462
Machine Tools; Internal Tab Washers for Slotted Round Nuts for Hook Spanner according to DIN 1804
Active
DIN 464
Knurled thumb screws, high type
Active
DIN 466
Knurled nuts, high type
Active
DIN 467
Knurled nuts, low type
Active
DIN 471
Circlips (retaining rings) for shafts; Normal type and heavy type
Hot rolled I-beams; wide flange I-beams heavy pattern, IPBv-serie; dimensions, masses, sectional properties
Active
DIN 1025-5
Hot rolled I-beams; medium flange I-beams, IPE-serie; dimensions, masses, sectional properties
Active
DIN 1301-1
Units - Part 1: Names and Symbols
Active
DIN 1301-2
Units - Part 2: Submultiples and Multiples for General Use
Active
DIN 1301-3
Units - Part 3: Conversions of Units No Longer To Be Used
Active
DIN 1302
General Mathematical Symbols and Concepts
Active
DIN 1303
Vectors, matrices, tensors; symbols and concepts
Active
DIN 1304-1
Letter symbols for physical quantities - Part 1: Symbols for general use
Active
DIN 1304-2
Letter symbols for physical quantities - Part 2: Symbols for use in meteorology and geophysics
Active
DIN 1304-3
Letter symbols for physical quantities - Part 3: Symbols for use in electric power engineering
Active
DIN 1304-5
Letter symbols for physical quantities - Part 5: Symbols for use in fluid mechanics
Active
DIN 1304-8
Letter symbols for physical quantities - Part 9: Symbols for use in the field of static converters using semiconductor devices
Active
DIN 1304-9
Letter symbols for physical quantities - Part 9: Symbols for equivalent circuits of piezoelectric crystals
Active
DIN 1311-1
(Mechanical) vibrations, oscillations and vibration systems - Part 1: Basic concepts, survey
Active
DIN 1311-2
(Mechanical) vibrations, oscillations and vibration systems - Part 2: Linear vibration systems with single degree of freedom
Active
DIN 1311-3
(Mechanical) vibrations, oscillations and vibration systems - Part 3: Linear time-invariant vibration systems with a finite number of degrees of freedom
Active
DIN 1311-4
Vibration; Vibrating Continua, Waves
Active
DIN 1313
Physical Quantities and Equation; Concepts, Methods of Writing
Active
DIN 1315
Angle; Concepts, Units
Active
DIN 1318
DIN 1324-1
Electromagnetic Field - Part 1. State Quantities
Active
DIN 1324-2
Electromagnetic Field - Part 2. Material Quantities
Active
DIN 1324-3
Electromagnetic Field - Part 3. Electromagnetic Waves
Active
DIN 1325-1
Vocabulary for value management, value analysis and functional analysis - Part 1: Value analysis and functional analysis
Active
DIN 1325-2
Value Management, Value Analysis, Functional Analysis Vocabulary - Part 2: Value Management
Active
DIN 1332
Acoustics; Symbols
Withdrawn
DIN EN ISO 80000-8
ISO 80000-8
DIN 1333
Presentation of Numerical Data
Active
DIN 1338
Writing and Typesetting of Formulae
Active
DIN 1355-1
Time; Calendar, Numbering of Weeks, Date of Day, (Clock) Time
Withdrawn
DIN 1421
Arrangement and Numbering in Texts; Clauses, Paragraphs, Enumerations
Active
DIN 1422-1
Publications in Sciences, Technology, Economy and Administration; Presentation of Manuscripts and Typoscripts
Active
DIN 1422-2
Publications in Sciences, Technology, Economy and Administration; Presentation of Clean Copies for Reprographic Use
Active
DIN 1422-3
Publications in Sciences, Technology, Economy and Administration; Typographical Presentation
Active
DIN 1422-4
Publications in Sciences, Technology, Economy and Administration; Presentation of Scientific and Technical Reports
Active
DIN 1440
Medium type washers for pins
Withdrawn
DIN EN 28738
ISO 8738
DIN 1443
Clevis pins without head
Withdrawn
DIN EN 22340
ISO 2340
DIN 1444
Clevis pins with head
Withdrawn
DIN EN 22341
ISO 2341
DIN 1450
Legibility of Typefaces – General
Active
DIN 1451-1
Lettering - Linear-Antiqua without serifes – General
Active
DIN 1451-2
Typefaces - lineal Linear-Antiqua; lettering for transportation
Active
DIN 1451-3
Lettering - Linear-Antiqua without serifes; lettering for printing
Active
DIN 1451-4
Typefaces - lineal Linear-Antiqua; stenciled lettering for engraving and other processes
Active
DIN 1463-1
Guidelines for the Establishment and Development of Thesauri; Monolingual Thesauri
Active
DIN 1463-2
Guidelines for the Establishment and Development of Thesauri; Multilingual Thesauri
Active
DIN 1470
Grooved Pins, Full Length Parallel-grooved with Pilot
Withdrawn
DIN EN 8739
ISO 8739
DIN 1471
Grooved Pins, Full Length Taper-grooved
Withdrawn
DIN EN 8744
ISO 8744
DIN 1472
Grooved Pins, Half Length Taper-grooved
Withdrawn
DIN EN 8745
ISO 8745
DIN 1473
Grooved Pins, Full Length Parallel-grooved with Chamfer
Withdrawn
DIN EN ISO 8740
ISO 8740
DIN 1474
Grooved Pins, Half Length Reverse-grooved
Withdrawn
DIN EN 8741
ISO 8741
DIN 1475
Grooved Pins, Third Length Centre-grooved
Withdrawn
DIN EN 8742
ISO 8742
DIN 1476
Round Head Grooved Pins
Withdrawn
DIN EN 8746
ISO 8746
DIN 1477
Countersunk Head Grooved Pins
Withdrawn
DIN EN 8747
ISO 8747
DIN 1481
Spring-Type Straight Pins (Roll Pins) - Heavy Type
Withdrawn
DIN EN ISO 8752
ISO 8752
DIN 1505-1
Bibliographic references to documents - Part 1: Full References to Printed and Published Documents
Active
DIN 1505-2
Bibliographic references to documents - Part 2: Rules for Citing
Active
DIN 1505-3
Bibliographic references to documents - Part 3: Indexes of cited documents (bibliographies)
Active
DIN 1511
Pattern Equipment for Foundries; Production and Quality
Withdrawn
DIN EN 12890
EN 12890
DIN 1530-1
Tools for moulding - Part 1: Ejector pins with cylindrical head
Active
DIN 1530-2
Tools for moulding - Part 2: Shouldered ejector pins
Active
DIN 1530-3
Tools for moulding - Part 3: Ejector pins with conical head
Keyboards for data and text input - Part 1: German keyboard layout
Active
DIN 2137-2
Keyboards for data and text input - Part 2: Additional requirements
Active
DIN 2342-1
Vocabulary of terminology; basic concepts
Active
DIN 2391-1
Seamless precision steel tubes - Part 1: Dimensions
Canceled
DIN EN 10305-1
EN 10305-1
DIN 2391-2
Seamless precision steel tubes - Part 2: Technical delivery conditions
Canceled
DIN EN 10305-1
EN 10305-1
DIN 2448
Seamless Steel Pipes and Tubes - Dimensions, Conventional Masses per Unit Length
Canceled
DIN EN 10220
EN 10220
DIN 2527
Blank flanges - Nominal pressure 6 to 100
Withdrawn
DIN EN 1092-1
EN 1092-1
DIN 2860
Capillary Fittings; Bends 180° of Copper
Withdrawn
DIN 2999-1
Pipe threads for tubes and fittings; parallel internal thread and taper external thread; tread dimensions
Withdrawn
DIN EN 10226-1
EN 10226-1
DIN 2999-2
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Internal Thread and Conical External Thread, Gauging System and Use of Gauges
Withdrawn
DIN EN 10226-3
EN 10226-3
DIN 2999-3
Whitworth Pipe Threads for Tubes and Fittings; Gauge Dimensions
Withdrawn
DIN EN 10226-3
EN 10226-3
DIN 2999-4
Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal thread
Withdrawn
DIN EN 10226-3
EN 10226-3
DIN 2999-5
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw Limit Ring Gauges for Gauging Conical External Threads, Sizes
Withdrawn
DIN EN 10226-3
EN 10226-3
DIN 2999-6
Whitworth Pipe Threads for Tubes and Fittings; Conical Screw Check Plugs, Sizes
Withdrawn
DIN EN 10226-3
EN 10226-3
DIN 4000 to DIN 4999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 4048-1
Water engineering, terms - Part 1: Dam plants
Active
DIN 4048-2
Water engineering, terms - Part 2: Waterpower plants
Active
DIN 4054
Correction of waterways, terms
Active
DIN 4094-1
Subsoil, Field investigations - Part 1: Cone penetration tests
Active
DIN 4102-1
Fire behaviour of building materials and elements - Part 1: Classification of building materials - Requirements and testing
Active
DIN 4102-2
Fire Behaviour of Building Materials and Building Components - Part 2: Building Components; Definitions, Requirements and Tests
Active
DIN 4102-3
Fire Behaviour of Building Materials and Building Components - Part 3: Fire Walls and Non-load-bearing External Walls; Definitions, Requirements and Tests
Active
DIN 4102-4
Fire behaviour of building materials and elements - Part 4: Overview and design of classified building materials, elements and components
Active
DIN 4102-5
Fire Behaviour of Building Materials and Building Components - Part 5: Fire Barriers, Barriers in Lift Wells and Glazings Resistant against Fire; Definitions, Requirements and Tests
Active
DIN 4102-6
Fire Behaviour of Building Materials and Building Components - Part 6: Ventilation Ducts; Definitions, Requirements and Tests
Active
DIN 4102-7
Fire behaviour of building materials and elements - Part 7: Roofing - Concepts, requirements and testing
Active
DIN 4102-8
Fire behaviour of building materials and components - Part 8: Small scale test furnace
Active
DIN 4102-9
Fire behaviour of building materials and elements - Part 9: seals for cable penetrations; concepts, requirements and testing
Active
DIN 4102-11
Fire behaviour of building materials and building components - Part 10: pipe encasements, pipe bushings, service shafts and ducts, and barriers across inspection openings; terminology, requirements and testing
Active
DIN 4102-12
Fire behaviour of building materials and elements - Part 12: Fire resistance of electric cable systems required to maintain circuit integrity - Requirements and testing
Active
DIN 4102-13
Fire behaviour of building materials and elements - Part 13: Fire resistant glazing; concepts, requirements and testing
Active
DIN 4102-14
Fire behaviour of building materials and elements - Part 14: Determination of the burning behaviour of floor covering systems using a radiant heat source
Active
DIN 4102-15
Fire behaviour of building materials and elements - Part 15: "Brandschacht"
Active
DIN 4102-16
Fire behaviour of building materials and elements - Part 16: "Brandschacht" tests
Active
DIN 4102-17
Fire behaviour of building materials and elements - Part 17: determination of melting point of mineral fibre insulating materials; concepts, requirements and testing
Active
DIN 4102-18
Fire behaviour of building materials and components - Part 18: fire barriers, verification of automatic closure (continuous performance test)
Active
DIN 4102-22
Fire behaviour of building materials and building components - Part 22: Application standard for DIN 4102-4 based on the design of partial safety factors
Active
DIN 4108-1
Thermal protection and energy economy in buildings - Part 1: Quantities and units
Active
DIN 4108-2
Thermal protection and energy economy in buildings - Part 2: Minimum requirements to thermal insulation
Active
DIN 4108-3
Thermal protection and energy economy in buildings - Part 3: Protection against moisture subject to climate conditions; Requirements and directions for design and construction
Active
DIN 4108-7
Thermal insulation and energy economy of buildings - Part 7: Airtightness of building, requirements, recommendations and examples for planning and performance
Active
DIN 4108-10
Thermal insulation and energy economy in buildings - Part 10: Application-related requirements for thermal insulation materials - Factory made products
Active
DIN 4150-1
Structural vibration - Part 1: Prediction of vibration parameters
Active
DIN 4150-2
Structural vibration - Part 2: Human exposure to vibration in buildings
Active
DIN 4150-3
Structural vibration - Part 3: Effects of vibration on structures
Active
DIN 4420-1
Service and working scaffolds - Part 1: Service scaffolds - Performance requirements, general design, structural design
Active
DIN 4512
Photographic sensitometry, determination of optical density: "Photographische Sensitometrie, Bestimmung der optischen Dichte" (1934-01, 1957-11, 1961-10)
Withdrawn
DIN 4512-1:1971-04, DIN 4512-3:1973-01, DIN 4512-4:1977-06, DIN 4512-5:1977-10, DIN 4512-6:1980-07
DIN 4512-1
Photographic sensitometry, determination of the speed of black and white negative materials for pictorial photography (1971-04, 1993-05)
Withdrawn (2000–09)
DIN ISO 6:1996-02
ISO 6
DIN 4512-3
Photographic sensitometry, determination of diffuse transmission density (1973-01)
Withdrawn
DIN 4512-7:1993-01, DIN 4512-8:1993-01, DIN 4512-9:1993-01
DIN 4512-4
Photographic sensitometry; determination of the speed of colour reversal films (1977-06, 1985-08)
Withdrawn (2002–06)
DIN ISO 2240:1998-06
ISO 2240
DIN 4512-5
Photographic sensitometry; determination of the speed of colour negative films (1977-10, 1990-11)
Withdrawn (2002–06)
DIN ISO 5800:1998-06
ISO 5800
DIN 4512-6
Photographic sensitometry; sensitometric illuminants and light sources (1980-07)
Withdrawn
DIN 4512-7
Photographic sensitometry, determination of optical density; concepts, symbols and notations (1993-01)
Active
DIN 4512-8
Photographic sensitometry, determination of optical density; geometric conditions for transmission density (1993-01)
Active
DIN 4512-9
Photographic sensitometry, determination of optical density; spectral conditions (1993-01)
Active
DIN 4512-10
Photographic sensitometry, determination of optical density; geometric conditions for reflection density (1993-01)
Active
DIN V 4701-10
Energy efficiency of heating and ventilation systems in buildings - Part 10: Heating, domestic hot water supply, ventilation
Active
DIN V 4701-12
Energetic evaluation of heating and ventilation systems in existing buildings - Part 12: Heat generation and domestic hot water generation
Physics of radiation in the field of optics and illuminating engineering - Part 1: Quantities, symbols and units of radiation physics
Active
DIN 5031-2
Physics of radiation in the field of optics and illuminating engineering - Part 2: Evaluation of radiation by different detectors
Active
DIN 5031-3
Physics of radiation in the field of optics and illuminating engineering - Part 3: Quantities, symbols and units of illuminating engineering
Active
DIN 5031-4
Physics of radiation in the field of optics and illuminating engineering - Part 4: Efficiencies
Active
DIN 5031-5
Physics of radiation in the field of optics and illuminating engineering - Part 5: Definitions for temperatures
Active
DIN 5031-6
Physics of radiation in the field of optics and illuminating engineering - Part 6: Pupil intensity as a measure of retinal illumination
Active
DIN 5031-7
Physics of radiation in the field of optics and illuminating engineering - Part 7: Terms for wavebands
Active
DIN 5031-8
Physics of radiation in the field of optics and illuminating engineering - Part 8: Definitions and constants of radiation physics
Active
DIN 5031-9
Physics of radiation in the field of optics and illuminating engineering - Part 9: Definitions in the field of luminescence
Active
DIN 5031-10
Physics of radiation in the field of optics and illuminating engineering - Part 10: Photobiologically effective radiation, quantities, symbols and actions
Active
DIN 5035-3
Artificial lighting - Part 3: Lighting of health care premises
Active
DIN 5035-6
Artificial lighting - Part 6: Measurement and evaluation
Active
DIN 5035-7
Artificial lighting - Part 7: Lighting of interiors with visual displays work stations
Active
DIN 5035-8
Artificial lighting - Part 8: Workplace luminaries - Requirements, recommendations and proofing
Active
DIN 5145
Plane irons for wood smooth and for planes
Active
DIN 5146
Curved irons for jack planes
Active
DIN 5406
Lockwashers and locking plates for use with rolling bearings
Active
DIN 5466-1
Splined joints, calculation of load capacity - Part 1: general basis
Active
DIN 5473
Logic and set theory; symbols and concepts
Active
DIN 5474
Signs in mathematical logic
Withdrawn
DIN 5473
DIN 5475-1
Complex quantities; nomenclature
Withdrawn
DIN 5483-3
DIN 5483-1
Time-dependent quantities - Part 1: Terms for the time-dependency
Active
DIN 5483-2
Time-dependent quantities - Part 2: Letter symbols
Active
DIN 5483-3
Time-dependent quantities - Part 3: Complex representation of sinusoidal time-dependent quantities
Active
DIN 5486
Notation of matrices
Withdrawn
DIN 1303
DIN 5487
Fourier-, Laplace- and Z-transformation; symbols and concepts
Active
DIN 5489
Directions and signs in electrical engineering; rules for electric and magnetic circuits, equivalent circuit diagrams
Withdrawn
DIN EN 60375
EN 60375
DIN 5493-2
Logarithmic quantities and units - Part 2: Logarithmic ratios, levels in nepers and decibels
Drive Type Fastenings without Taper Action – Part 1: Parallel Keys, Keyways, Deep Pattern
Active
DIN 6885-2
Drive Type Fastenings without Taper Action – Part 2: Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and Application
Active
DIN 6885-3
Drive Type Fastenings without Taper Action – Part 3: Parallel Keys, Shallow Pattern, Dimensions and Application
Active
DIN 6900
Screw and Washer Assemblies
Withdrawn
DIN EN 10644
EN 10644
DIN 6901
Tapping screw and washer assemblies
Withdrawn
DIN EN 10510
EN 10510
DIN 6902
Plain washers for screw and washer assemblies
Withdrawn
DIN EN 10673
EN 10673
DIN 6903
Plain washers for tapping screw and washer assemblies
Withdrawn
DIN EN 10669
EN 10669
DIN 6912
Hexagon socket thin head cap screws with pilot recess
Active
DIN 6914
High-strength hexagon head bolts with large widths across flats for structural steel bolting
Withdrawn
DIN EN 14399-4
EN 14399-4
DIN 6916
Round washers for high-strength structural steel bolting
Withdrawn
DIN 6921
Hexagon flange bolts
Withdrawn
DIN EN 1665
EN 1665
DIN 6922
Hexagon flange bolts with reduced shank
Withdrawn
DIN EN 1665
EN 1665
DIN 6923
Hexagon nuts with flange
Withdrawn
DIN EN 1661
EN 1661
DIN 6924
Prevailing torque type hexagon nuts with nonmetallic insert
Withdrawn
DIN EN ISO 7040, DIN EN ISO 10512
ISO 7040, ISO 10512
DIN 6925
Prevailing torque type all-metal hexagon nuts
Withdrawn
DIN EN ISO 7042, DIN EN ISO 10513
ISO 7042, ISO 10513
DIN 6926
Prevailing torque type hexagon nuts with flange and with non-metallic insert
Withdrawn
DIN EN 1663, DIN EN 1666
ISO 7043 (modified), ISO 12125 (modified)
DIN 6927
Prevailing torque type all-metal nuts with flange
Withdrawn
DIN EN 1664, DIN EN 1667
ISO 7044 (modified), ISO 12126 (modified)
DIN 7000 to DIN 7999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 7045
Pan head screws with type H or type Z cross recess - product grade A
Active
DIN 7245
Saw blades for web saws
Active
DIN 7337
Break mandrel blind rivets
Withdrawn
DIN EN ISO 14589, DIN EN ISO 15977, DIN EN ISO 15978, DIN EN ISO 15979, DIN EN ISO 15980, DIN EN ISO 15981, DIN EN ISO 15982, DIN EN ISO 15983, DIN EN ISO 15984, DIN EN ISO 16582, DIN EN ISO 16583, DIN EN ISO 16584
ISO 14589, ISO 15977, ISO 15978, ISO 15979, ISO 15980, ISO 15981, ISO 15982, ISO 15983, ISO 15984, ISO 16582, ISO 16583, ISO 16584
DIN 7343
Spiral Pins; Normal Type
Withdrawn
DIN EN ISO 8750
ISO 8750
DIN 7344
Spiral Pins; Heavy Duty Type
Withdrawn
DIN EN ISO 8748
ISO 8748
DIN 7346
Spring-Type Straight Pins; (Roll Pins) Light-weight Type
Withdrawn
DIN EN ISO 13337
ISO 13337
DIN 7349
Plain Washers for Bolts with Heavy Clamping Sleeves
Active
DIN 7500-1
Thread rolling screws for metric ISO thread - Part 1: Types, designation, requirements
Withdrawn
ISO 7085
DIN 7500-2
Thread rolling screws for ISO metric thread; guideline values for hole diameters
Active
DIN 7504
Self-drilling screws with tapping screw thread - Dimensions, requirements and testing
Withdrawn DIN EN ISO 10666, DIN EN ISO 15480, DIN EN ISO 15481, DIN EN ISO 15482, DIN EN ISO 15483
ISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483
DIN 7513
Hexagon head and slotted head thread cutting screws - Dimensions, requirements and testing
Active
DIN 7516
Cross recessed head thread cutting screws - Dimensions, requirements and testing
Active
DIN 7603
Ring seals and gaskets
Active
DIN 7875
Diving accessories for skin divers; terminology
Withdrawn
DIN 7876
Diving accessories for skin divers; flippers. dimensions. requirements and testing)
Withdrawn
DIN 7877
Diving accessories for skin divers; diver"s masks. requirements and testing
Withdrawn
DIN 7962
Cross recesses for screws; (modified version of ISO 4757)
Withdrawn
DIN EN ISO 4757
ISO 4757
DIN 7970
Threads and thread ends for tapping screws (modified version of ISO 1478)
Withdrawn
DIN EN ISO 1478
ISO 1478
DIN 7971
Slotted pan head tapping screws
Withdrawn
DIN ISO 1481
ISO 1481
DIN 7972
Slotted countersunk head tapping screws
Withdrawn
DIN ISO 1482
ISO 1482
DIN 7973
Slotted raised countersunk head tapping screws
Withdrawn
DIN ISO 1483
ISO 1483
DIN 7977
Taper Pins with Thread Ends and Constant Point Lengths
Withdrawn
DIN EN 28737
ISO 8737
DIN 7978
Taper Pins with Internal Thread
Withdrawn
DIN EN 28737
ISO 8736
DIN 7979
Parallel Pins with Internal Thread
Withdrawn
DIN EN ISO 8733, DIN EN ISO 8735
ISO 8733, ISO 8735
DIN 7980
Spring lock washers with square ends for cheese head screws
Withdrawn
DIN 7981
Cross recessed pan head tapping screws
Withdrawn
DIN ISO 7049
ISO 7049
DIN 7982
Cross recessed countersunk head tapping screws
Withdrawn
DIN ISO 7050
ISO 7050
DIN 7983
Countersunk (Flat) Head Tapping Screws with Cross Recess
Withdrawn
DIN ISO 7051
ISO 7051
DIN 7984
Hexagon socket thin head cap screws
Active
DIN 7985
Cross recessed raised cheese head screws
Withdrawn
DIN EN ISO 7045
ISO 7045
DIN 7991
Hexagon socket countersunk head cap screws
Withdrawn
DIN EN ISO 10642
ISO 10642
DIN 8000 to DIN 8999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 8074
Polyethylene (PE) pipes – Dimensions
Active
DIN 8075
Polyethylene (PE) pipes - PE 63, PE 80, PE 100, PE-HD - General quality requirements, testing
Active
DIN 8513-1
Brazing and Braze Weld Filler Metals; Copper Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery
Withdrawn
DIN EN 1044
EN 1044
DIN 8513-2
Brazing and Braze Weld Filler Metals; Silver-bearing Brazing Alloys with less than 20% by wt. Silver; Composition, Use, Technical Conditions of Delivery
Withdrawn
DIN EN 1044
EN 1044
DIN 8513-3
Brazing filler metals; silver brazing filler metals containing not less than 20% of silver; composition, application, technical delivery conditions
Withdrawn
DIN EN 1044
EN 1044
DIN 8513-4
Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery
Withdrawn
DIN EN 1044
EN 1044
DIN 8513-5
Brazing filler metals; Nickel base filler metals for high temperature brazing; Application, composition, technical delivery conditions
Withdrawn
DIN EN 1044
EN 1044
DIN 8580
Manufacturing processes - Terms and definitions, division
Active
DIN 8806-1
Narrow band saw blades for woodworking; dimensions
Active
DIN 9000 to DIN 9999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 9021
Plain washers with large outside diameter
Withdrawn
DIN EN ISO 7093-1, DIN EN ISO 7093-2
ISO 7093-1, ISO 7093-2
DIN 10000 to DIN 19999
DIN 10000 to DIN 10999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 10504
Food hygiene - Lamps for the lighting of meat and meat products
Withdrawn
DIN 11000 to DIN 11999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 11850
Tubes for the food, chemical and pharmaceutical industry - Stainless steel tubes - Dimensions, materials
Active
DIN 12000 to DIN 12999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 12950-1
Laboratory furniture; safety cabinets for microbiological and biotechnological work; safety requirements, tests
Withdrawn
DIN 12950-2
Laboratory furniture; safety cabinets for microbiological and biotechnological work; containment of class 1 and class 2 cabinets, microbiological test
Withdrawn
DIN 12950-10
Laboratory furniture; safety cabinets for microbiological and biotechnological and biotechnological work; requirements and testing
Withdrawn
DIN 12975-1
Thermal solar systems and components - Solar collectors - Part 1: General requirements
DIN 12975-2
Thermal solar systems and components - Solar collectors - Part 2: Test methods
DIN 12976-1
Thermal solar systems and components - Factory made systems - Part 1: General requirements
DIN 12976-2
Thermal solar systems and components - Factory made systems - Part 2: Test methods
DIN 13000 to DIN 13999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 13080
Division of hospitals into functional areas and functional sections
Active
DIN 13260-2
Supply systems for medical gases - Part 2: Dimensions and allocation of probes and gas-specific connection points for terminal units for compressed medical gases and vacuum
Active
DIN 13432
Packaging - Requirements for packaging recoverable through composting and biodegradation - Test scheme and evaluation criteria for the final acceptance of packaging
Active
DIN EN 13432
DIN 13715
Workpiece cornes and edges
Active
DIN ISO 13715(2000–12)
DIN 14000 to DIN 14999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 14090
Areas for the fire brigade on premises
Active
DIN 14096-1
Fire precaution regulation - Part 1: General and part A (placard); rules for drafting and placarding
Active
DIN 14096-2
Fire precaution regulation - Part 2: Part B (for persons without special tasks of fire prevention and fire fighting); rules for drafting
Active
DIN 14096-3
Fire precaution regulation - Part 3: Part C (for persons with special tasks of fire prevention and fire fighting); rules for drafting
Active
DIN 14210
Water pool for firefighting
Active
DIN 14236
Ultrasonic domestic gas meters
Active
DIN 14406-4
Portable fire extinguishers - Part 4: Maintenance
Active
DIN 14503
Trailers for firefighting purposes, two-wheeled; general requirements
Withdrawn
DIN 14521
DIN 14505
Firefighting and rescue service vehicles - Vehicles for roller containers - General requirements
Active
DIN 14507
Rescue service vehicles - Vehicles for roller containers - General requirements
Active
DIN 14520
Trailers for portable fire pumps
Withdrawn
DIN 14521
Firefighting - Trailer with removable foam-water monitor
Active
DIN 14530-5
Fire fighting vehicles - Part 5: Group pumping appliance LF 10/6, Group pumping appliance for rescue operations HLF 10/6
Active
DIN 14530-11
Fire fighting vehicles - Part 11: Group pumping appliance LF 20/16, Group pumping appliance for rescue operations HLF 20/16
Active
DIN 14530-16
Fire fighting vehicles - Part 16: Pumping appliance TSF
Active
DIN 14530-17
Fire fighting vehicles - Part 17: Pumping appliance TSF-W
Active
DIN 14530-21
Fire fighting vehicles - Part 21: Pump water tanker TLF 20/40, Pump water tanker TLF 20/40-SL
Active
DIN 14530-22
Fire fighting vehicles - Part 22: TLF 16/24-TR
Active
DIN 14530-24
Fire fighting vehicles - Part 24: Small pumping appliance KLF
Active
DIN 14530-25
Fire fighting vehicles - Part 25: Pumping appliance STLF 10/6
Active
DIN 14555-1
Vehicles carrying tools and gears - Part 1: General requirements
Active
DIN 14555-3
Vehicles carrying tools and gears - Part 3: Emergency tender RW
Active
DIN 14555-12
Vehicles carrying tools and gears - Part 12: Damage control tender GW-G
Active
DIN 14555-21
Vehicles carrying tools and gears - Part 21: GW-L1 for logistic tasks
Active
DIN 14555-22
Vehicles carrying tools and gears - Part 22: GW-L2 for logistic tasks
Active
DIN 14565
Fire hose tender; Type SW 2000-TR
Withdrawn
DIN 14701-1
Turntable ladders and similar fire fighting vehicles; Purpose, concepts, safety equipment, requirements
Withdrawn
DIN EN 1777
EN 1777
DIN 14701-2
Turntable ladders and similar fire fighting vehicles; Turn table ladders, engine driven
Withdrawn
DIN EN 14043, DIN EN 14044
EN 14043, EN 14044
DIN 14701-3
Turntable ladders and similar fire fighting vehicles; Rescue baskets
Withdrawn
DIN EN 1777
EN 1777
DIN 14702
Turntable ladder DL 16-4, hand operating
Active
DIN 14703
Trailer Ladder AL 16-4
Active
DIN 14710-1
Hook ladder, manufactured using wood; with hinged hook
Withdrawn
DIN EN 1147
EN 1147
DIN 14710-3
Hook light metal ladder
Withdrawn
DIN 14711-1
Scaling ladder; made from wood
Withdrawn
DIN EN 1147
EN 1147
DIN 14711-2
Scaling ladder; made from light metal
Withdrawn
DIN EN 1147
EN 1147
DIN 14711-3
Scaling ladder; socket rungs and socket parts
Withdrawn
DIN EN 1147
EN 1147
DIN 14713
Folding ladder
Withdrawn
DIN EN 1147
EN 1147
DIN 14715-1
Three piece extension ladder made from wood
Withdrawn
DIN EN 1147
EN 1147
DIN 14715-2
Three piece extension ladder; made of light metal
Withdrawn
DIN EN 1147
EN 1147
DIN 15000 to DIN 15999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 15018-2
Cranes; steel structures; principles of design and construction
Active
DIN 15185-1
Warehouse systems with guided industrial trucks; requirements on the ground, the warehouse and other requirements
Active
DIN 15185-2
Warehousesystems with powered industrials trucks; code of practice for the protection of persons when operating with trucks in narrow aisles; safety requirements, testing
Active
DIN 15721
Film 70 mm; projection reel
Active
DIN 16000 to DIN 16999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 16518
Classification of types
Active
DIN 16892
Cross-linked high-density polyethylene (PE-X) pipes - General quality requirements and testing
Materials for permanent magnets: Technical conditions
Active
DIN 17457
Withdraw
DIN EN 10217-7
DIN 17458
Withdraw
DIN EN 10216-5
DIN 17471
Resistance alloys
Active
DIN 18000 to DIN 18999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 18012
House service connections facilities - Principles for planning
Active
DIN 18013
Recesses for meter boards (electric meters)
Active
DIN 18014
Foundation earth electrode - General planning criteria
Active
DIN 18015-1
Electrical installations in residential buildings - Part 1: Planning principles
Active
DIN 18015-2
Electrical installations in residential buildings - Part 2: Nature and extent of minimum equipment
Active
DIN 18015-3
Electrical installations in residential buildings - Part 3: Wiring and disposition of electrical equipment
Active
DIN 18022
Domestic kitchens, bathrooms and WCs; design principles
Withdrawn
DIN 18024-1
Barrier-free built environment - Part 1: Streets, squares, paths, public transport, recreation areas and playgrounds - Design principles
Active
DIN 18024-2
Construction of accessible buildings - Part 2: Publicly accessible buildings and workplaces, design principles
Active
DIN 18065
Stairs in buildings - Terminology, measuring rules, main dimensions
Active
DIN 18379
Construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV) - Installation of air conditioning systems
Active
DIN 18382
Contract procedures for building works - Part C: General technical specifications for building works; Low-voltage installation and medium-voltage installation with nominal voltages up to including 36 kV
Active
DIN 18384
Construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV); Installation of lightning protection systems
Active
DIN 18800-1
Steel structures - Part 1: Design and construction
Withdrawn
DIN EN 1993 DIN EN 1090
DIN 18800-2
Steel structures - Part 2: Analysis of safety against buckling of linear members and frames
Withdrawn
DIN EN 1993
DIN 18800-3
Steel structures - Part 3: Analysis of safety against buckling of plates
Withdrawn
DIN EN 1993
DIN 18800-4
Steel structures - Part 4: Analysis of safety against buckling of shells
Withdrawn
DIN EN 1993
DIN 18800-5
Steel structures - Part 5: Composite structures of steel and concrete - Design and construction
Withdrawn
DIN EN 1994
DIN 18800-7
Steel structures - Part 7: Execution and constructor's qualification
Active
EN 1090-2
DIN 19000 to DIN 19999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN V 19222
Control technology – Terminology
Active
DIN 19225
Measurement and control; terminology and classification of controllers
Active
DIN 19226-1
Control technology - Part 1: General terms and definitions
Active
DIN 19226-2
Control technology - Part 2: Terms and definitions; dynamic systems behaviour
Active
DIN 19226-3
Control technology - Part 3: Terms and definitions of switching systems behaviour
Active
DIN 19226-4
Control technology - Part 4: Terms and definitions of control systems
Active
DIN 19226-5
Control technology - Part 5: Functional terms
Active
DIN 19226-6
Control technology - Part 6: Terms and definitions of functional and constructional units
Active
DIN 19227-1
Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions
Active
DIN 19227-2
Control technology; graphical symbols and identifying letters for process control engineering; representation of details
Active
DIN 19237
Measurement and control; control engineering vocabulary
Withdrawn
DIN 19226-3, DIN 19226-4, DIN 19226-5, DIN 19226-6
DIN 19227-1
Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions
Withdrawn
DIN EN 62424
DIN 19227-2
Control technology; graphical symbols and identifying letters for process control engineering; representation of details
Active
DIN 19533
Pipe-lines of high-density PE (high-density polyethylene) and low-density PE (low density polyethylene) for drinking water supply; pipes, pipe connections and fittings for pipe-lines
Withdrawn
DIN EN 12201-1, DIN EN 12201-2, DIN EN 12201-3, DIN EN 12201-5
EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-5
DIN 19704-1
Hydraulic steel structures - Part 1: Criteria for design and calculation
Active
DIN 19704-2
Hydraulic steel structures - Part 2: Design and manufacturing
Active
DIN 19704-3
Hydraulic steel structures - Part 3: Electrical equipment
Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type A; solder termination for free wiring
Active
DIN 41750-5
Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type C; crimp termination for free wiring
Active
DIN 41782
Guidelines for the presentation of published data
Withdrawn
DIN IEC 60747-2
IEC 60747-2
DIN 41786
Thyristors, definitions
Withdrawn
DIN 41855
Semiconductor devices and integrated circuits; kinds of devices and general terms
Withdrawn
DIN 41855-2
Semiconductor devices and integrated circuits; optoelectronic semiconductor devices; terms and definitions
Withdrawn
DIN 41868
Cases 10 A 3 and 10 B 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-1
Case 23 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-2
Cases 34 A 2 and 34 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-3
Case 11 A 3 and 11 B 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-4
Case 12 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-5
Case 13 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-6
Case 14 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-7
Case type 15 for semiconductor devices; main dimensions
Withdrawn
DIN 41873
Cases type 5 for semiconductor devices and integrated circuits
Withdrawn
DIN 41876
Cases 18 A, B and C with 2 up to 4 terminals for semiconductor devices; main dimensions
Withdrawn
DIN 42400
Terminal markings for electrical equipment; general rules, alphanumeric system
Withdrawn
DIN EN 60445
EN 60445
DIN 42402
Terminal markings for power transformers and reactors
Active
DIN 42403
Terminal markings for power converters
Withdrawn
DIN IEC 61148
IEC 61148
DIN 42673-1
Totally enclosed fan-cooled three-phase induction motors squirrel-cage, type IM B 3, with rolling bearing; mounting dimensions and relationship frame sizes-output ratings
Withdrawn
DIN 42673-2
Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection increased safety "e"
Active
DIN 42673-3
Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection flameproof enclosure "d"
Active
DIN 42673-4
Totally-enclosed fan-cooled alternating-current polyphase motors with squirrel-cage, design B3, with ball bearings, maximum envelope dimensions
Active
DIN 42961
Rating plates for rotating electrical machinery; design
Active
DIN 42973
Rated output values for rotating electrical machinery for continuous duty
Active
DIN 43700
Measurement and control - Measurement and control instruments for panel mounting - Nominal front- and cut-out-dimensions
Withdrawn
DIN IEC 61554
IEC 61554
DIN 43780
Electrical measuring instruments; direct acting indicating electrical measuring instruments and their accessories
Withdrawn
DIN EN 60051-1
EN 60051-1
DIN 43802-2
Line scales and pointers for indicating electrical measuring instruments; general requirements
Active
DIN 43802-3
Line scales and pointers for indicating electrical measuring instruments; designs and dimensions
Active
DIN 43802-4
Line scales and pointers for indicating electrical measuring instruments; scale graduation and numbering
Active
DIN 43807
Measuring and control; electrical measuring instruments; terminal markings for switchboard meters, panel meters and measuring transducers for the measurement of power and power factor
Active
DIN 43856
Electricity meters, tariff time switches and ripple control receivers; connection diagrams, terminal marking, circuit diagrams
Active
DIN 43856-2
Electricity meters - Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995
Active
DIN 43870-1
Meter mounting boards; dimensions based on a grid system
Active
DIN 43870-2
Meter mounting boards; functional area
Active
DIN 43870-3
Meter panels; wirings
Active
DIN 44070-1
Meter mounting boards; dimensions based on a grid system
Active
DIN 44070-2
Meter mounting boards; functional area
Active
DIN 44070-3
Meter panels; wirings
Active
DIN 44070-4
Meter panels; cover for wiring
Active
DIN 44080
Thermistors; PTC, technical terms and tests
Withdrawn
DIN 44300
Information processing; vocabulary
Withdrawn
DIN 44300-1
Information processing - Concepts - General terms
Withdrawn
DIN 44300-2
Information processing - Concepts - Representation of data
Withdrawn
DIN 44300-3
Information processing - Concepts - Data structures
Withdrawn
DIN 44300-4
Information processing - Concepts – Programming
Withdrawn
DIN 44300-5
Information processing - Concepts - Components of digital computer systems
Withdrawn
DIN 44300-6
Information processing - Concepts – Storage
Withdrawn
DIN 44300-7
Information processing - Concepts – Times
Withdrawn
DIN 44300-8
Information processing - Concepts - Processing functions
Withdrawn
DIN 44300-9
Information processing - Concepts - Process relations and modes of operation
Withdrawn
DIN 45322
Circular connectors for radio and associated sound equipment; six-pole connectors
Withdrawn
DIN EN 60130-9
EN 60130-9
DIN 45323
Connectors for coupling an external low-voltage power to portable entertainment equipment (describes at least two DC coaxial power plugs)
Active
DIN 45500-1
High fidelity audio equipment and systems; minimum performance requirements; Part 1: general
Withdrawn
DIN EN 61305-1
EN 61305-1
DIN 45500-2
High fidelity audio equipment and systems; requirements for tuner equipments
Withdrawn
DIN EN 61305-2
EN 61305-2
DIN 45500-3
High fidelity audio equipment and systems; requirements for disk record reproducing equipments
Withdrawn
DIN 45500-4
High fidelity audio equipment and systems; minimum performance requirements for magnetic recording and reproducing equipment
Withdrawn
DIN 45500-5
High fidelity audio equipment and systems; minimum performance requirements for microphones
Withdrawn
DIN 45500-6
High fidelity audio equipment and systems; minimum performance requirements for amplifiers
Withdrawn
DIN EN 61305-3
EN 61305-3
DIN 45500-7
High fidelity audio equipment and systems; requirements for loudspeakers
Withdrawn
DIN EN 61305-5
EN 61305-5
DIN 45500-8
High fidelity audio equipment and systems; for sets and systems
Withdrawn
DIN 45500-10
High fidelity audio equipment and systems; minimum performance requirements for headphones
Withdrawn
DIN 45507
Measuring apparatus for frequency variations in sound recording equipment
Withdrawn
DIN IEC 60386
IEC 60386
DIN 45539
Disk record reproducing equipment; directives for measurements, markings and audio frequency connections, dimensions of interchangeable pickups, requirements of play back amplifiers
Withdrawn
DIN IEC 60098
IEC 60098
DIN 45596
Microphones; phantom powering
Withdrawn
DIN 46400-1
Steel flats with special magnetic properties cold rolled, non - oriented, finally annealed magnetic sheet and strip hysteresis loss at frequencies above 100 Hz
Withdrawn
DIN EN 10106
EN 10106
DIN 46400-3
Grain-oriented magnetic steel and strip technical conditions
Withdrawn
DIN EN 10107
EN 10107
DIN 47100
Cords for telecommunication; code of insulated conductors, colour of sheath
Withdrawn
DIN 47301-1
Terms of HF-lines
Active
DIN 47301-2
Terms of HF-lines
Active
DIN 47301-3
Definition of radio frequency transmission lines - mean characteristic impedance - mean standing wave ratio
Active
DIN 48803
Lightning protection system; Arrangement of components and dimensions for mounting
Withdrawn
DIN 48830
Lightning protection system; Description
Withdrawn
DIN 50000 to DIN 59999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 51097
Testing of floor coverings; determination of the anti-slip properties: wet-loaded barefoot areas; walking method; ramp test
Withdrawn
DIN 51130
DIN 51130
Testing of floor coverings; determination of the anti-slip properties: workrooms and fields of activities with slip danger, walking method - ramp test
Font CMC 7 for magnetic ink character recognition; characters and nominal dimensions
Withdrawn
DIN ISO 1004
ISO 1004
DIN 66008-1
Font A for optical character recognition; characters and nominal dimensions
Active
DIN 66008-6
Font A for optical character recognition; characters and nominal dimensions; extension of the character set
Active
DIN 66008-7
Font A for optical character recognition; representation of characters by dots in a 9 × 9 matrix
Active
DIN 66009
Font B for optical character recognition; character
Withdrawn
DIN 66020-1
Functional requirements for the interface between data terminal equipment and data circuit-terminating equipment - Part 1: General application
Active
DIN 66020-2
List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) in public data networks
Active
DIN 66020-4
Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)
Active
DIN 66020-9
Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48000 bits per second
Active
DIN 66021-1
Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)
Active
DIN 66021-2
Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48000 bits per second
Active
DIN 66025-1
Numerical control of machines, format; general requirements
Active
DIN 66025-2
Industrial automation; numerical control of machines; format, preparatory and miscellaneous functions
Active
DIN 66027
Information processing; programming language FORTRAN
Withdrawn
DIN 66215-1
Programming of numerically controlled machines; CLDATA, general structure and record types
Active
DIN 66215-2
Programming of numerically controlled machines; CLDATA; minor elements of type 2000 records (post-processor commands)
Active
DIN 66253-2
Information processing; programming language PEARL
Information processing; programming language Pascal
Withdrawn
DIN 66257
Numerical control of machines; concepts
Withdrawn
DIN ISO 2806
ISO 2806
DIN 66258-1
Interfaces and basic data link control procedures for data communication; C S-interface, V S-interface
Withdrawn
DIN 66258-2
Interface and basic data link control procedures for data communication; balanced interface for start-stop transmission using basic data link control procedures on point-to-point connection
Withdrawn
DIN 66261
Information processing; Nassi-Shneiderman flowchart symbols
Active
DIN 66264-1
Industrial automation systems and integration - Multiprocessor Control System for Industrial Machines (MPST) - Part 1: Parallel bus
Active
DIN 66264-2
Multiprocessor control system for industrial machines (MPST); industrial automatics; rules for information interchange
Active
DIN 66303
Information technology - 8 bit code
Active
DIN V 66304
Industrial automation; Computer Aided Design; format for the exchange of standard parts data
Active
DIN 66325-2
Local and Metropolitan Area Networks; LLC; identical with ISO 8802-2:1989
Withdrawn
ISO 8802-2
DIN 66325-4
Local and Metropolitan Area Networks; token-passing bus access method; identical with ISO/IEC 8802-4:1990
Withdrawn
ISO/IEC 8802-4
DIN 69901
Project controlling; project management; concepts
Active
DIN 70000 to DIN 79999
DIN
TITLE
STATUS
DIN REPLACEMENT
OTHER ORG REPLACEMENT
DIN 71412
Lubricating nipples; cone type
Active
DIN 72311-1
Lead storage batteries; starter batteries for motorcycles, nominal capacities, main dimensions
Active
DIN 72311-4
Lead storage batteries; starter batteries, terminals, vent plugs and filler openings
Active
DIN 72311-8
Lead storage batteries; starter batteries for motor cycles and passenger cars
Active
DIN 72311-13
Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45 and 54 Ah, for lateral basic fastening 10,5
Active
DIN 72311-16
Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45, 54 and 63 Ah, for lateral basic fastening 19
Active
DIN 72311-17
Lead storage batteries; starter batteries, protective covering for terminal
Active
DIN 72311-18
Lead storage batteries; starter batteries with basic fastening 10,5 for passenger cars and commercial vehicles; nominal capacities, main dimensions
Active
DIN 72311-20
Lead storage batteries; starter batteries for commercial vehicles; nominal capacities and main dimensions
Active
DIN 72311-21
Lead storage batteries; starter batteries with 10,5 basic fastening lugs for commercial vehicles; nominal capacities and main dimensions
Active
DIN 72552-1
Terminal markings for motor vehicles; scope, principles, requirements
Tags: List of DIN standards, Informatics Engineering, 464, List of DIN standards This is an incomplete list of DIN standards, The, STATUS, column gives the latest known status of the standard, If a standard has been withdrawn and no replacement specification is listed either the specification was withdrawn without replacement or a replacement specification could not be identified, DIN stands for, Deutsches Institut für Normung, me, List of DIN standards, English, Instruction Examples, Tutorials, Reference, Books, Guide pasar, pts-ptn.net